Wood / Leather sports steering wheel

• Turn the ignition key to position “0”. Remove the ignition key from the ignition switch
• Wait at least five minutes. Then disconnect the battery negative lead before separating the connectors or removing other electrical equipment.

• Turn the steering wheel a quarter turn so that the holes on the reverse of the steering wheel are accessible.

• Insert a screwdriver in the hole (2) on the reverse of the steering wheel, at right angles to the rear surface of the steering wheel.Insert the screwdriver as far as possible to determine the position of the end of the spring clip (1)
• Position the end of the screwdriver on the top of the spring clip as illustrated
• Pry the screwdriver upwards towards the upper edge of the hole (2) so that the end of the screwdriver presses the spring clip down (1) until one side of the steering wheel module springs out and releases from the mounting
• Turn the steering wheel a half turn in the opposite direction. Carry out the same operation on the other side.
• Turn the steering wheel to the neutral position.

• Fold the steering wheel module out
• Remove the two connectors (1) for the ignition cables for the airbag. First press in the catches on the sides. Then pull the connectors straight out.

Примечание: The connectors are tightly secured. However, tools must not be used when removing.
- Place the steering wheel module to one side.

Remove:

• the connector (1)
• the screw (2) that holds the steering wheel, leave the steering wheel in place.

Remove:

• the screw (1). Install the screw in the contact reel (2)
• the steering wheel. Pull the wiring out through the hole in the steering wheel.

• Remove the screw (1). Remove the ground lead.

Applies to cars without a RTI keypad installed on the steering wheel when installing a wooden or leather steering wheel

• Remove the three screws (2). Lift the horn out (3)
• Place the steering wheel to one side.

Applies to cars with an RTI keypad installed on the steering wheel when installing a leather steering wheel

• Remove the three screws (2). Disconnect the horn (3).

Applies to cars with an RTI keypad installed on the steering wheel when installing a leather steering wheel

• Carefully twist the horn upwards. Position the horn as illustrated
• Remove the connector for the RTI keypad installed on the steering wheel. First press the catches (1) in. Pull the connector out
• Place the horn to one side.

Applies to cars with an RTI keypad installed on the steering wheel when installing a leather steering wheel

Remove:

• the two screws in the mounting for the RTI keypad
• the mounting. Press out the keypad from the steering column cover
• Place the steering wheel to one side.

Applies to cars with vibration dampers

• Remove the screw (2). Remove the vibration damper (1)
• Place the steering wheel to one side.

• Take the new steering wheel.

Applies to cars with vibration dampers

• Install the vibration damper in the new steering wheel. Tighten using the screw, see point ru-RU0900c8af8013202b#KC01144857.

Примечание: Ensure that the screw is correctly tightened. Check that the vibration damper is secured. The screw is self tapping which may mean that it is difficult to screw in.

Applies to cars with an RTI keypad mounted on the steering wheel

• Install the RTI keypad on the new steering wheel, see point ru-RU0900c8af8013202b#KC01144856. Ensure that the cable harness is positioned underneath the steering wheel spoke.

• Reinstall the horn in the steering wheel, see point ru-RU0900c8af8013202b#KC01144854 - ru-RU0900c8af8013202b#KC01144855. Check that the three springs underneath are correctly positioned. Ensure that the ground lead is not trapped
• Install the three screws in the horn. Tighten the screws crosswise. Tighten to 8 ±2 Nm (6 ± 1.5 ft.lb).

Примечание: The screws are self tapping.
- Reinstall the ground lead. Tighten the ground lead.

Примечание: Ensure that the screw is correctly tightened. Check that the ground lead is secure. The screw is self tapping which may mean that it is difficult to screw in.
- Check the function of the horn by press the horn around its entire circumference. A metallic noise should be heard when the three contact points come into contact.

• Insert the cable harness through the hole in the new steering wheel and through the holder (3)
• Carefully install the new steering wheel by holding it straight and aligning the locating pins (1) on the contact reel
• Remove the screw from the contact reel. Reinstall the screw in the holder. See point ru-RU0900c8af8013202b#KC01144853
• Install the new screw (2). Tighten to 40 Nm (30 lbf ft.)
• Connect the connector (4).

• Check that the two springs (1) are in position
• Press the two connectors for the ignition cables for the airbag into the steering wheel module
• Insert the two pins on the reverse of the steering wheel module in the two springs. Ensure that the ignition cables are not trapped
• Press the steering wheel module into the mountings. (Two clicks should be heard).

• Turn the ignition key to position “II”
• Reconnect the battery negative lead.