TV NTSC/PAL

• Turn the ignition key to position O
• Cars with manual gearboxes: Remove the ignition key
• Disconnect the battery negative lead.

Примечание: Wait at least five minutes before disassembling the connectors or removing other electrical equipment.

• Remove the seat cushion (1). First pull the front edge of the seat cushion up. Pull the cushion forwards. Then lift the seat cushion out.

• Fold both the rear backrests forward
• Remove the seat belts from the guides (1).

• Remove the clip (1) at the side of the left-hand side cushion
• Pull the top edge of the left front cargo compartment panel out to access the upper lock for the side cushion
• Repeat the operation on the right-hand side.

• Remove the left-hand side cushion. First press in the catches (1) at the top edge of the reverse of the side cushion. Pull the cushion out slightly
• Grasp the cushion using both hands. Twist counter-clockwise until the catches on the inside release
• Remove the side cushion. First pull out the upper edge of the side cushion. Then pull upwards
• Repeat the operation on the other side.

• Remove the cover and the screw for the left-hand C-post panel
• Repeat the operation on the other side.

• Remove the rubber strip at the rear edge on the left-hand rear door frame
• Grasp the top edge of the C post panel. Pull (A) the panel inwards until the three clips (1) release
• Then pull (B) the panel straight up. Place the panel to one side
• Repeat the operation on the other side.

• Carefully lift the front edge of the parcel shelf panel until the clips (1) release
• Lift up the panel further until the locating pins (2) release from their holes
• Pull out the parcel shelf. Lay the parcel shelf on the folded backrests.

• Remove the cargo compartment carpet at the rear edge. First turn the two handles (1) 90°.

• Pull up the front of the cargo compartment carpet. Fold the front half back over the rear half of the cargo compartment carpet.

• Slide the entire cargo compartment carpet forward slightly. Twist slightly to remove the cargo compartment carpet through the tailgate opening
• Remove the cargo compartment carpet.

• Press the centres of the clips at the lower edge of the foldable side panel on the left-hand side until a click is heard
• Remove the two clips
• Remove the plastic nut at the front lower edge of the side panel.

Remove:

• the clips (1) in the left front side panel in the cargo compartment
• the panel. Place the panel to one side.

• Remove the cable (1) between the GPS antenna on the parcel shelf and the foremost of the three upper sockets in the upper sockets in the RTI control module
• Place the cable to one side. The amplifier will not be reused. A new cable harness is in the kit.

• Route the new cable harness (1) in the same way as the old harness
• Position the connectors for the cable harness at the C-posts and at the rear edge of the wheel house. See the illustration
• Press the cable harness into place in the parcel shelf with the existing clips
• Connect the connector to the GPS antenna.

Applies to Japan

• Remove the ground lead for the rear windshield. First remove the screw (1). Remove the connector (2) from the rear windshield at the right-hand C-post
• Place the ground lead and the screw to one side. They will not be reused.

Applies to Europe

• Remove the screw (1). Remove the ground lead from the C-post. A new screw is included in the kit.

• Remove the cables (1, 2) for the existing antenna amplifier on the left C-post
• Remove the screw (3) and remove the antenna amplifier
• Place the antenna amplifier to one side. The amplifier will not be reused.

• Connect the new TV antenna amplifier (blue) to the new AM/FM antenna amplifier (blue) from the kit.

Applies to Japan

• Carry out the same operation with the green antenna amplifiers.

Applies to Europe

• For the EU only use the small green TV antenna amplifier.

Applies to Japan

• Install the new AM/MPX and TV antenna amplifiers (green) on the right C-post. Ensure that the antenna amplifier guide lugs engage in the two rectangular holes and in the small round holes
• Tighten the amplifiers
• Repeat the operation for the left-hand AM/FM and TV antenna amplifier (blue).

Applies to Europe

• Install the small green TV antenna amplifier for the right hand C post in the rear position with the ground lead cable terminal on top. Tighten the antenna amplifier
• Ensure that the amplifier guide lugs are in their relevant holes
• Repeat the operation for the left-hand AM/FM and TV antenna amplifier (blue).

• Reinstall the cables (1) (that were removed earlier) in the front antenna amplifier on the left C-post
• Connect the two single cables (2) (that were routed earlier) to the rear antenna amplifier on the left C-post
• Connect the cables (3, 4, 5) to the connectors on the rear windshield as illustrated.

Applies to Japan

• Connect the two single cables (1) (that were routed earlier) to the rearmost of the two amplifiers on the right C-post
• Connect the cables (2, 3, 4) to the connectors on the rear windshield as illustrated.

Applies to Europe

• Connect the single cable (1) (previously routed) to the front terminal in the TV antenna amplifier on the right C-post as illustrated
• Connect the cables (2) to the connectors on the rear windshield as illustrated.

• Clamp the cables on the parcel shelf, at the C-post and at the lead-in to the cargo compartment. See the arrows in the illustration.

• Remove the three screws (1) holding the CD ROM changer and bracket at the body
• Lift up the unit and place it on the left rear side member.

• Take the TV tuner (1) and the three screws (2) from the kit. Tighten the TV tuner on the reverse of the bracket for the CD ROM changer
• Connect the cable harness (3) with the green connector and the new DIN cable (4) to the TV tuner
• Reinstall the CD ROM changer and the TV tuner.

• Connect the two cables (1) from the TV tuner to the RTI control module
• Connect the two cables (2) routed from the parcel shelf to the TV tuner
• Connect the cable (3) from the parcel shelf to the RTI control module
• Clamp the cables with a tie strap (4) from the kit.

Reinstall:

• the parcel shelf panel
• the C-post panels
• the side cushions
• the backrests
• the seat cushion
• the panels in the cargo compartment.

• Turn the ignition key to position II
• Reconnect the battery negative lead
• Re-position the cargo compartment carpet
• Program the software according to the service information in VIDA.