CD - changer

• Move the left front seat to the rearmost position.

• Turn the ignition key to position O
• Cars with manual gearboxes: Remove the ignition key
• Disconnect the battery negative lead.

Примечание: Wait at least five minutes before disassembling the connectors or removing other electrical equipment.

• Remove the panel in front of the gear selector lever. Pry off the panel using a plastic weatherstrip tool
• Shift the gear selector lever to the rearmost position.

• Remove the two screws from the dashboard environment panel.

• Angle the dashboard environment panel outwards so that it is possible to insert a couple of fingers between the centre console and the side of the dashboard environment panel
• Pull the dashboard environment panel downwards while maintaining the same angle. Remove the dashboard environment panel. Some force is required because the panel is tightly installed. Disconnect the connectors on the reverse of the dashboard environment panel. Put the dashboard environment panel to one side.

Примечание: If any of the outer hooks break off, these must be repaired. The method for this can be found in the Workshop Manual in the section about the dashboard.

• Remove the screws from the radio bracket
• Pull out the bracket with the radio. Pull the lower corner while pressing downwards
• Disconnect the radio connectors. Remove the bracket with the radio.

Remove:

• the left side panel (1) from the centre console. First turn the screw clip. Pull the panel outwards and backwards
• the sill trim panel (2) at the left front door
• the covers (3) and the screws (4).

• Tip the left front seat backwards
• Fold the floor carpet forward to access the air ducts (1).

• Remove the seat cushion (1). First pull the front edge of the seat cushion up. Pull forwards. Then lift the seat cushion out.

• Remove the sill moulding from the left-hand rear door.

• Fold the left hand rear backrest forward
• Remove the seat belt from the guide (1).

• Remove the clip (1) at the side of the left-hand side cushion
• Pull the top edge of the left front cargo compartment panel out to access the upper catch for the side cushion.

• Remove the left-hand side cushion. First press in the catches (1) at the top edge of the reverse of the side cushion. Pull out slightly
• Grasp the side cushion using both hands. Twist counter-clockwise until the catches on the inside release
• Remove the side cushion. First pull out the upper edge of the side cushion. Then pull upwards.

• Remove the cargo compartment carpet at the rear edge. First turn the two handles (1) 90°.

• Pull up the front of the cargo compartment carpet. Fold the front half back over the rear half of the cargo compartment carpet.

• Slide the entire cargo compartment carpet forward slightly. Twist slightly to remove the cargo compartment carpet through the tailgate opening
• Remove the cargo compartment carpet.

• Press the centres of the clips at the lower edge of the foldable side panel on the left-hand side until a click is heard
• Remove the two clips
• Remove the plastic nuts at the front and lower edges of the side panel.

• Turn the handle (1) on the left-hand side through 90°
• Fold the side panel inwards. Lift the side panel out. Place the side panel to one side. A new panel is in the kit.

Remove:

• the clips (1) in the left front side panel in the cargo compartment
• the panel. Place the panel to one side. A new panel is in the kit.

• Route the new DIN cable for the CD changer up between the front air duct (1) and the stay (2) for the centre console
• Route the cable through the radio compartment
• Clamp the cable to the stay. Use the tie strap (3) from the kit
• Route the cable above and along the front air duct to the seat mounting member (4)
• Clamp the wiring to the existing cable harness (5).

• Route the cable (1) under the carpet along the left side of the car to the rear door
• Install protective caps on the lugs (2) for the cable duct
• Route the cable further above and along the front cable duct (3). Continue along the right hand side of the rear cable duct (4).

• Connect the ground lead for the new shorter cable harness (1) to the rear ground terminal (2) under the seat cushion
• Route both cables (1, 3) along the two cable ducts (4) under the insulation panel. Continue out through the hole in the car body to the cargo compartment
• Disconnect the four connectors in the front cable duct. Position the wiring under these. Reconnect the connectors again.

• Remove the rear electronic module. First open the catch (1) on the top of the module. Fold the module forward. Lift the module from the mountings (2).

• Connect the new routed red and white cable to the fuse socket (2) on the fuse holder
• Install a 10A fuse in fuse holder 10
• Reinstall the electronic module.

• Remove the transport screws (1.2)
• Install the dust cover (3) over the holes for the transport screws.

• Check that the catches (1.2) point towards the mark V, vertical position. If not: move the catches to mark V.

• Install the brackets (1, 2) on the CD changer. Use the screws (3) from the kit.

• Install both new clips and nuts (1) in the panel on the side member (2) and at the rear edge of the wheel housing flange (3)
• Position the CD changer by the electronic module in the cargo compartment.

• Connect the new routed DIN cable (1) to the CD changer
• Connect the pre routed cable and the blue connector (2) to the CD changer
• Install the CD changer, tighten the screw (3) for the clip with the nut at the rear edge of the wheel house flange and the screws (4) for the side member and the rear crossmember.

• Secure the wiring at the cable harness by the fuse holder and at the left hand side of the rear cable duct. Use tie straps (1) (from the kit).

• Insert the radio in the radio tray. Connect the CD changer connector and the other connectors to the radio
• Reinstall the bracket with the radio. Tighten the bracket and radio using the screws (1)
• Connect the connectors to the dashboard environment panel. Reinstall the dashboard environment panel
• Reinstall the panel in front of the gear selector lever
• Fold back the carpet
• Reinstall the centre console side panel and the sill trim panels in the left-hand front and rear doors
• Fold the left-hand front seat back into position
• Install the screws from the kit. Tighten to40 Nm (30 ft.lb). Reinstall the covers
• Install the two new panels in the left hand side of the cargo compartment
• Reinstall the side cushion
• Fold the backrest back into place
• Reinstall the seat cushion.

• Turn the ignition key to position II
• Reconnect the battery negative lead
• Re-position the cargo compartment carpet
• Program the software according to the service information in VIDA.